Embest
 Low cost ARM Evaluation Boards

New products to receive literature  fill in request
 

These Embest ARM Evaluation Boards can of course be used with any ARM development system.  If you have not already chosen a JTAG interface and compiler then for a very cost effective solution you should consider the Embest JTAG interface, ARM IDE software based on the GCC compiler and Flash Programmer. They support a wide range of ARM7 and ARM9 cores from ATMEL, SAMSUNG, PHILIPS, CIRRUS, LINKUP, OKI, Sharp and ST Microelectronics.  

COMSOL holds a full range of Embest development tools and their most popular EVBs in stock for next day delivery via our web site.

Samsung S3CEB2410 Evaluation Board

The Embest S3CEB2410 evaluation board is a development platform based on the Samsung S3C2410X processor. The S3C2410X consists of 16-/32-bit RISC (ARM920T) CPU core, separate 16KB instruction and 16KB data cache, MMU to handle virtual memory management, LCD controller (STN & TFT), NAND flash boot loader, System Manager (chip select logic and SDRAM controller), 3-ch UART, 4-ch DMA, 4-ch Timers with PWM, I/O ports, RTC, 8-ch 10-bit ADC and touch screen interface, I²C-BUS interface, IIS-BUS interface, USB host, USB device, SD host & multimedia card interface, 2-ch SPI and PLL for clock generation. The Embest S3CEB2410 evaluation board can be used as a development platform, either with the aim of using the board in the target application or using this board as a reference design for a custom board.

Hardware specification

Also contains:

Embest Provide Source code examples, users manual, circuit schematic, WinCE4.2 BSP, embedded Linux source tree (porting for this board), PSU

Samsung SBC2410-I Single Board Computer

ARM920T Single-board Computer based on the Samsung S3C2410 with full Bus and Peripheral Signal Expansion and capable of supporting Linux, WinCE or any embedded operating system.

The SBC2410-I is a full-featured single board computer (SBC) using the Samsung S3C2410 processor, which is based on the ARM920T architecture. This 16/32 bit RISC architecture can operate at 200MHz and contains a memory management unit making it a suitable platform for stand alone applications, embedded real time operating systems and complex OS such as Linux or WinCE.

The SBC2410-I supports a variety of onboard peripherals such as a serial Flash, 64Mbyte NOR Flash, 128Mbyte SDRAM, 2-channel USB Host and 1-channel USB Device, interfaces for buzzer, battery backed RTC, and reset button. In addition to this, expansion connections are made available via a number of header connectors to support LCD, touch screen, matrix keypad, SD card and JTAG debugging. Source code examples are provided with the SBC2410-I giving the designer the ability to both understand hardware operation and also to quickly develop applications. Optional LCD display hardware is available for this development board and can be easily connected to an existing header. Sample test software is provided for this interface.

Hardware specification

Power supply: +5V Samsung S3C2410 (ARM920T core with MMU capable of 200+ MHz operation) LCD Display interface (STN or TFT) Touch-screen interface 4x4 Matrix Keypad interface SD card interface and holder Bluetooth port (UART0) RS232 port (can support GPS, UART1) RS232 port for PC communications (UART2) 2-channel USB Host and 1-channel USB Device 1MByte Serial Flash

256Kbit Serial EEPROM (I²C) RTC (battery backed) 32MByte NOR Flash (64M optional) 64MByte SDRAM (128M optional) Buzzer JTAG debug port Reset button Status LEDs 96 pin expansion connector with external access to data and address 32 bits GPIO 8 x 10 bits Analogue input 3 interrupts

Also contains:

Testing software for hardware, user manual, circuit schematic drawing and PCB Layout, BOM list and parts datasheet

 

Samsung SBC2410-II Single Board Computer

The SBC2410-II is another full-featured single board computer (SBC) released by Embest. The 16/32-bit S3C2410 processor is based on the ARM920T architecture and can operate at 200MHz. It contains a memory management unit making it a suitable platform for stand alone applications, embedded real time operating systems and complex operating systems such as Linux or WinCE.

The Embest SBC2410-II single board computer takes advantage of the S3C2410 ARM920T microcontroller, supporting a variety of onboard memory and peripherals such as 1MByte NOR Flash, 64MByte NAND Flash, 64MByte SDRAM, 1 USB Host and 1 USB Device, RS232 port, a 10M Ethernet interface, AC97, battery backed RTC, LEDs, test and reset buttons. In addition to this, expansion connections are made available via a number of header connectors and support peripheral LCD hardware, touch screen, matrix keypad, SD card, 3 serial ports, JTAG and 36 GPIOs.

The SBC2410-II is capable of supporting Linux and WinCE OS. Linux source code and WindowsCE4.2.net BSP are provided with this board. Also plenty of example programs are included, which greatly help the designer to better understand the hardware operations and also speed-up development. The design provides an ideal embedded computer platform and can be used not, only as a development board, but also as a powerful single board computer.

Hardware specification

Dimensions: 120x90mm Working temperature: -20~70 Celsius Power supply: +5V Samsung S3C2410 (ARM920T core with MMU capable of 266 + MHz operation) Flash: 1MByte NOR Flash, 64MByte NAND Flash SDRAM: 64MByte LCD Display interface (STN or TFT) 10M Ethernet interface (RJ-45 interface) One RS232 serial port 3 serial ports available 10pin Keyboard interface

96 pin expansion connector with external access to data and address lines 8 x 10 bit A/D 1 USB Host and 1 USB Device Audio Input/Output RTC (battery backed) SD card interface and holder 4 Status LEDs 4 Test buttons Power switch Reset button 20pin standard JTAG interface 36 bits GPIO

Also contains:

Software (including interface code examples, Boot Loader, Linux port and Windows CE4.2 net Board Support Package), user manual, circuit schematic drawing & datasheets
 

Samsung SBC2410-III Computer

The SBC2410-III is a cost-effective application-ready board integrating Samsung's ARM9 S3C2410A using an ultra-compact kernel board mounted directly on top of a carrier board.

Embest SBC2410-III computer uses a kernel board providing most of the CPU functions and has a S3C2410A CPU, 64MByte NAND Flash, 32MByte SDRAM on it. The carrier board has signal conditioning for various peripherals on it, such as USB Host, USB Device, hard disk port, serial ports, Ethernet interface, LCD interface, audio, battery, LEDs, test and reset buttons, etc.

In order to offer users a fast time-to-market and a customizable and flexible reference platform, the board is preloaded with Linux and provided with compiler, kernel, bootloader, etc.

Hardware specification

Dimensions: 135x169mm (carrier board), 58x36mm (kernel board) Working temperature: -20~70 Celsius Power supply: +12V Samsung S3C2410A (ARM920T core with MMU capable of 266+ MHz operation) 64MByte NAND Flash 32MByte SDRAM LCD interface (STN or TFT, support resolution up to 1024x768) 10M Ethernet interface 3 serial ports

1 USB Host and 1 USB Device Audio in/out (supports playing mp3, wav and some other formats files) RTC (battery backed) SD/MMC card interface 4 User LEDs 4 User keys Power switch Reset button 4 x 10 bit A/D 20pin standard JTAG interface IDE44 port: for 2.5" hard disk

Also contains:

Software (including Compiler Linux port, Boot Loader and Flash Programmer utilities), many interface code examples, user manual, circuit schematic drawing, parts datasheet & Embest products reference

 

Samsung SBC2440-I Computer

The SBC2440-I is a ready-to-use single board computer using Samsung’s 16/32-bit S3C2440 processor based upon the ARM920T architecture. It can operate at 400MHz and is designed to provide hand-held devices and general applications with lowpower, and high-performance microcontroller solution in small die size. It has a built-in NAND flash boot loader so that high-density NAND flash memory can be used without having to install an additional support chip. The SBC2440-I features two Ethernet ports and supports a variety of other onboard peripherals such as 1Mbyte NOR Flash, 64Mbyte NAND Flash, 64Mbyte SDRAM, USB Host and USB Device, RS232 and TTL, IDE interface, battery backed RTC, LEDs, reset buttons. Expansion connections are available via a number of header connectors that support peripheral LCD hardware, touch screen, matrix keypad, SD card, JTAG and 16 GPIOs. It comes with Linux 2.6.13 source code, WindowsCE4.2.net BSP and drivers for serial port, CS8900A, DM9000, RTC, USB Host, User LEDs, LCD, Touch panel, ADC, USB camera/mouse/keyboard/U-disk etc.

Hardware Specification

Dimensions: 134 x 95mm Working temperature: -20~70 Celsius Power supply: +12V Samsung S3C2440A (ARM920T core with MMU capable of 400MHz operation) Flash: 1Mbyte NOR Flash (support 2Mbyte for option), 64Mbyte NAND Flash 64Mbyte SDRAM LCD Display interface (STN or TFT, support resolution up to 1024x768) Touch-screen interface 10/100M Ethernet interface Mic (Audio input) Phone (Audio output) RS232 serial port 3 serial ports available through 14pin (2.0mm space) interface

2 serial ports available through ST16C2550 chip extension USB host USB device (USB camera/mouse/keyboard/U-disk) RTC (battery backed) SD/MMC card socket 4 Status LEDs 1 Power switch 1 Reset button 1 x 10pin standard JTAG interface GPIO expansion connector 44pin standard IDE interface SupportsWinCE, Palm OS, Symbian and Linux

Supplied with:

Linux 2.6.13 source code, WindowsCE4.2.net BSP and drivers for serial port, CS8900A, DM9000, RTC, USB Host, User LEDs, LCD, Touch panel, ADC, USB camera/mouse/keyboard/U-disk
 

Samsung SBC2440-II Computer

The SBC2440-II is a single board computer using Samsung’s S3C2440 processor operating at 400MHz. The 16/32-bit RISC microprocessor has interfaces for LCD controller (STN & TFT), System Manager (chip select logic and SDRAM controller), 3-ch UART, 4-ch DMA, I/O ports, RTC, 8-ch 10-bit ADC and touch screen interface, I²C BUS interface, IIS-BUS interface, USB host, USB device, SD host & Camera interface, 2-ch SPI and PLL for clock generation. Due to its small size and low power consumption, it is well suited for portable and mobile products. It supports a variety of onboard peripherals such as 64Mbyte NAND Flash, 64Mbyte SDRAM, USB Host and USB Device, serial ports, Ethernet interface, camera interface, battery backed RTC, LEDs, reset buttons. Expansion connections are available via a number of header connectors and support peripheral LCD hardware, touch screen, SD card, JTAG, system bus and GPIOs. The SBC2410-II supports Linux and WinCE OS and comes with Linux 2.6.13 source code and WindowsCE4.2.net BSP.

Hardware Specification

Dimensions: 120x100mm Working temperature: 0~70 Celsius Power supply: +12V Samsung S3C2440A (ARM920T core with MMU capable of 400MHz operation) 64Mbyte NAND Flash 64Mbyte SDRAM LCD Display interface (STN or TFT, support resolution up to 1024x768) Touch-screen interface 10M Ethernet interface Audio in/out (UDA1341) 1 RS232 serial port 3 serial ports available through 14pin (2.0mm space) interface

USB Host and USB Slave RTC (battery backed) SD/MMC card socket 4 Status LEDs 4 User buttons 3.3V power indicator Reset button 20pin standard JTAG interface Camera interface 34pin GPIO expansion connector 44pin system bus interface Supports Linux andWinCE OS

Supplied with:

Test software for hardware, user manual, circuit schematic drawing and parts datasheet

Samsung S3CEV40 Evaluation Board

The Embest S3CEV40 Evaluation Board for S3C44B0X is a platform that is suitable for code development of Samsung's S3C44B0X 16/32-bit RISC microcontroller (General ARM) for hand-held device and general applications.

The S3C44B0X CPU is a 16-/32-bit RISC (ARM7TDMI) CPU core with 8KB cache, optional internal SRAM, LCD controller (up to 256 colour DSTN), 2-ch UART with handshake (IRDA1.0,16-byte FIFO), 4-ch DMA, System manager (chip select logic, FP/EDO/SDRAM controller), 6-ch timers with PWM, 71-bit general purpose I/O, RTC, 8-ch 10-bit ADC, I²C-BUS interface, I²S-BUS interface, Sync. SIO interface and PLL for clock.

The EVB consist of a S3C44B0X, boot Flash, SDRAM, LCD & TSP touch screen interface, two serial communication ports, Ethernet interface, USB interface, keyboard interface, IIS (sound) interface, exterior IDE port, NAND Flash, RTC, JTAG interface and an 8 segment display.

5.0V DC or USB power supply 2 M bytes 16-bit Flash 8 M bytes 16-bit SDRAM 4K bit EEPROM with I²C BUS Two serial ports Reset button two interrupt buttons and two LEDS external IDE port LCD & TSP touch screen port 20-pin JTAG interface connector USB connecter 4 groups of 2×20 PIN expansion connectors	10M Ethernet interface connector 8 segment display IIS Interface: Speaker & Microphone 16 M Bytes NAND Flash 320×240 LCD * Option 4×4 keyboard * Option
	Now available as a low price Embest Kit containing....   This evaluation board,   UNetICE JTAG interface   Single seat  IDE, GCC Compiler,                   Debugger & Programmer For cost see the web shop

Also contains:

Test source routes, uCos on uCLinux, Source trees, Schematic, BOM, PSU

Samsung AX4510 Evaluation Board

Embest AX4510 EVB for S3C4510B is a platform that is suitable for code development of Samsung's S3C4510B(ARM7TDMI) RISC microcontroller (General ARM) for network applications and general applications.

The S3C4510B is based on 16/32-bit ARM7TDMI RISC processor. It offers a configurable 8K-byte unified cache/SRAM and Ethernet controller which reduces total system cost. Important peripheral functions include two HDLC channels with buffer descriptor, two UART channels, 2-channel GDMA, two 32-bit timers, and 18 programmable I/O ports. On-board logic includes an interrupt controller, DRAM /SDRAM controller, and a controller for ROM/SRAM and flash memory. The System Manager includes an internal 32-bit system bus arbiter and an external memory controller.

Embest AX4510 EVB consist of S3C4510B, boot Flash, SDRAM, LCD interface, two serial communication ports, Ethernet interface, USB interface, PS2 interface, exterior IDE port, JTAG interface and LED. Embest AX4510 EVB provide a high performance and low cost solution for embedded engineers.

Dimensions: 177 x 130 mm 5.0V DC or USB power supply 4 M bytes Flash(2M x 16bit) 16 M bytes SDRAM(2M x 32bit) 2K x 8 EEPROM 2x RS232 USB connecter 10M/100M Ethernet interface connector(RJ45) IDE44 port: for 2.5" hard disk

LCD port 2 PS2 port 4 key buttons Reset button 4 LEDS Beeper 20-pin JTAG interface connector all the pins of CPU expand out

Also contains:

Source code software examples and test software, bootloader source codes, ucLinux source tree, user manual and circuit schematic

Samsung Mini2410-I Processor Card

The Mini2410-I board integrates Samsung's S3C2410X processor, which is based on an ARM920T core with integrated MMU.

Dimensions: 67.6 x 45 mm
Temperature: 0 to +70 Celsius
Samsung's S3C2410 microcontroller based on a 2.5V Static ARM920T CPU core with MMU
64Mbyte SDRAM
1/2/4/8Mbyte NOR flash
On-chip MPLL inputs the 12MHz OSC to run the MCU at up to 203MHz
32768Hz RTC (Real-time clock)
20-pin standard JTAG-interface
16bit data bus, I/O and all other hardware interfaces expansions via DIMM 200-pin connection
Boot via NAND Flash on carrierboard or NOR Flash in Processor, jumper selectable
Single 3.3V power supply

Also contains:

Software examples, users manual, circuit schematic and BOM list

 

Samsung Mini2410-II Processor Card

The Mini2410-II board integrates Samsung's S3C2410A processor, which is based on an ARM920T core with integrated MMU.

Dimensions: 58 x 36 mm
Temperature: -20 to +70 Celsius
Samsung's S3C2410A microcontroller based on a 2.5V Static ARM920T CPU core with MMU
32Mbyte SDRAM
64Mbyte Nand Flash
On-chip MPLL inputs the 12MHz OSC to run the MCU at up to 203MHz
32768Hz RTC (Real-time clock)
LAN, Audio, AD, SPI, Uart, USB, I2C, RTC and all other hardware interfaces are extended via two 2.0mm space 56-pin biserial dip connectors.
Single 3.3V power supply

Also contains:

Software examples, users manual, circuit schematic and BOM list

Samsung Mini2410-III Processor Card

The Mini2410-III board integrates Samsung's S3C2410A processor, which is based on an ARM920T core with integrated MMU.

Dimensions: 50 x 60 mm
Temperature: 0 to +70 Celsius
Samsung's S3C2410A microcontroller based on an ARM920T CPU core with MMU
64Mbyte SDRAM (32Mbyte optional)
64Mbyte Nand Flash (32Mbyte optional)
2Mbyte Nor flash
128Kbyte SRAM
On-chip MPLL generates the 12MHz OSC up to operate MCU at up to 203MHz
32768Hz RTC (battery backed)
1.0mm space 8-pin JTAG interface
ADC, PWM, LCD, UART, IIS, SPI, TSP, Watchdog, I2C, USB, SD/MMC Card, Ethernet, I/O and all other hardware interfaces can be extended via two 4mm height 0.6mm space 140-pin board-to-board connectors.

Also contains:

Software examples, users manual, circuit schematic and BOM list

Samsung Mini44B0 Processor Card

The Mini44B0 is based on the Samsung SC344B0x an ARM7TDMI core. The ARM7TDMI includes the Thumb decompressor, an on-chip ICE breaker debug support and a 32-bit hardware multiplier. The processor card takes full advantage of the integrated on-chip functions and the peripherals of S3C44B0x.

Samsung’s S3C44B0x microcontroller
2.5V Static ARM7TDMI CPU core with 8Kbytes cache
8Mbyte SDRAM
1/2/4Mbyte NOR flash
On-chip PLL inputs the 8MHz oscillator to run the MCU at up to 66MHz
32,768Hz RTC (Real-time clock)
16- bit data bus, I/O and all other hardware interfaces expansions via DIMM 200-pin connection
20-pin standard JTAG-interface
Little/Big endian mode selection via CPU jumper setting
Single 3.3V power supply
Dimensions: 67.6mm x 49mm
Temperature: 0~+70º
SAM-BOOT utility to load flash via COM port

Also contains:

Source code software examples, users manual, circuit schematic and BOM list